Safety weights
Safety weights – also known as two-piece weights – are used primarily in original equipment.
Important: Safety weights are supplied without a spring. Please order the matching retaining spring separately.
The weight for professionals
Safety weights – also known as two-piece weights – consist of the weight body and a retaining spring that sits between the rim flange and the tire. This design is used mainly in original equipment and prevents damage to the rim.
Types and matching retaining springs
Every safety weight requires the matching retaining spring. The following overview shows the assignment:
| Type | Original part from | Spring for steel rims | Spring for alloy rims |
|---|---|---|---|
| Type 260 | Volkswagen (also identical platforms, e.g. ŠKODA, SEAT) | V3-Zn (5812-0271-302) | V3-Zn (5812-0271-302) |
| Type 261 | Mercedes-Benz | M1-Zn (5812-0191-502) | MA-Zn (5812-0201-302) |
| Type 274 | BMW, MINI | B1 (5812-7420-101) | B3 (5812-7410-301) |
| Type 280 | Volkswagen Commercial Vehicles, VOLVO | V3-Zn (5812-0271-302) | V3-Zn (5812-0271-302); VOLVO: B3 (5812-7410-301) |
Please note the approvals:
- For BMW, two-piece weights are approved only for a certain proportion of the alloy rims used. All other alloy rims must be fitted with adhesive weights 390.
- For Mercedes-Benz, safety weights are not approved for all alloy rims. Where adhesive weights are specified, adhesive weight 360 must be used.
Fitting safety weights
For professional fitting you need tire bead breaker pliers – manual or pneumatic – and a spring lifter. With these two tools you can fit the weights without damaging the rim.
Step 1: Insert the spring
Using the tire bead breaker pliers, press the tire away at the point where the weight is to be fitted, far enough for the rim flange to be exposed. Insert the retaining spring at the desired point and remove the tire bead breaker pliers. This presses the retaining spring between the rim flange and the tire so that it sits firmly in place.
Step 2: Attach the weight
Lift the spring with the spring lifter far enough for the weight body to be pushed underneath. Slide the weight in the required gram size centrally under the spring. Then slowly tilt the spring lifter back so that the retaining spring can engage in the recess provided in the weight body.
Frequently asked questions about safety weights
No. Safety weights are supplied without springs. Please order the matching retaining spring separately, according to the intended use, in the category Springs for safety weights.
- Safety weight type 260: V3-Zn (5812-0271-302)
- Safety weight type 261: steel rims M1-Zn (5812-0191-502), alloy rims MA-Zn (5812-0201-302)
- Safety weight type 274: steel rims B1 (5812-7420-101), alloy rims B3 (5812-7410-301)
- Safety weight type 280: standard V3-Zn (5812-0271-302), VOLVO alloy rims B3 (5812-7410-301)
You need tire bead breaker pliers – manual or pneumatic – and a spring lifter. You will find both in the category Balance weight fitting.
The safety weights are original parts from Volkswagen, Volkswagen Commercial Vehicles, Mercedes-Benz, BMW, MINI and VOLVO, among others. As identical platforms are in some cases also used by the manufacturers' companies abroad (e.g. ŠKODA, SEAT), the weights are suitable there as well. By vehicle type you can filter between motorcycle, passenger car, van and motorhome.
Yes – in combination with the respective matching retaining spring. Two restrictions must be observed: for BMW, two-piece weights are approved only for a certain proportion of the alloy rims used; all other alloy rims must be fitted with adhesive weights 390. For Mercedes-Benz, safety weights are not approved for all alloy rims; where adhesive weights are specified, adhesive weight 360 must be used.